There was one way to get a ready-to-use StuffIt Expander installer: You will need an appropriate version (for example, 4.0.1 or 5.5) of StuffIt Expander for the decoding/decompression at the Centris.Īn additional difficulty is that you will need StuffIt Expander for the decoding/decompression. Just transfer downloaded files completely unaltered. If the modern Mac for some reason decodes/decompresses automatically, use a PC for the downloads. Do not use StuffIt Expander or another decoding/decompression application on the modern Mac or on a PC. Any Mac application files need to be encoded or at least compressed in order to arrive undamaged at the Centris. >The Centris has absolutely no add-on software, just the basic OS. Everything would allow you to mount Zip disks without the need for any other application. We should not rule out the possibility that Mt. There may be downloads elsewhere as well. Everything can be found at (see also the 00disk-abstracts.txt file). Unfortunately, this web page appears to be available only via the Wayback Machine (2016) now. The original home page with the version 1.5.5 (for 68k) was. I hope it can fit onto a single 1.44MB floppy disk. Note: For users who have Microsoft Windows 98, 2000, ME or later the drive should be automatically detected and installed, but the default installation will not install the Iomega Tools.ĭrivers for the Iomega Zip drives is on our removable and tape drive drivers page.>I will look for Mt. Use the disk included with your Zip drive (on floppy or CD (compact disc)) to install the drivers for your Zip drive. Once the drive has been installed and automatically or manually configured in BIOS, additional software needs to be installed. It is important to note that older computers may not properly detect an IDE/EIDE device and it may be required that a BIOS update be obtained.įor additional help and information, see: Computer BIOS help and support. In BIOS, verify that the IDE/EIDE device is either set up as Auto or is set up as a 100 MB HDD. How to enter and exit the BIOS or CMOS setup.Then, as the computer is booting, enter the BIOS setup. After you install your drive, turn on your computer. We do not recommend you connect all the cables yet because if there are issues, you may have to disconnect them again.Īs with any IDE/EIDE device, a Zip drive must be properly configured in your computer's BIOS. BIOS setupĪfter connecting the Zip Drive, replace the case back and connect the keyboard, monitor, and power to the computer. This cable is often keyed and only goes in one direction. When connecting the IDE/EIDE cable to the back of the Zip drive, connect the power cable to the back of the drive. It should connect with the colored side of the cable facing the power connection. Often, the red or blue side of the cable represents pin 1. Once the Zip disk drive has been installed into the computer, connect the IDE/EIDE interface cable to the back of the zip drive. The front bezel is only obtainable through the computer manufacturer.įor links to many computer and hardware manufacturers, see our support listing. Visit a local computer store for alternate brackets.Contact the computer manufacturer for drive brackets compatible with your computer.If your computer does not accept the drive bracket, you may want to consider any of the below recommendations. Drive brackets are included with the internal zip disk drive package. If no 3.5-inch drive bay is available, the computer needs a drive bracket and partial front bezel to cover the empty portion. Drive baysĪn internal zip drive is always going to occupy or need a 3.5-inch drive bay. The Zip drive is set as the secondary device. When installing the IDE/EIDE zip drive ensure that the Zip drive has the proper jumper setting. When physically installing the zip disk drive, ensure the computer is powered down and unplugged.Ensure you are familiar with ESD (electrostatic discharge) and its potential dangers.Write down important information from the top or bottom of the hard drive, such as the model number, serial number, and its specifications.Updated: by Computer Hope Before getting started
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |